Latest Post

Sallen Key Lowpass Butterworth Filter Calculator

-

This calulator allows you to calculate filter component values of Sallen Key Lowpass Butterworth and Bessel Filter. See the frequency and phase response of filter in by clicking PLOT GRAPH button. First calculate component values of Filter by clicking COMPUTE and then click on Plot Graph button to get response of filter.


Sallen Key Lowpass Filter
Input Output
R1 (Ohms)  
Cutoff Freq (Hz)  
R2 (Ohms)  
C1 (F)  
C2 (F)  
Plot Response
Actual Cutoff Frequency (Hz)  
Q

Filter Response


Comments

  1. UnknownMay 28, 2021 at 1:42 AM

    I think C1 and C2 are reported as backwards from the diagram.

    ReplyDelete

Post a Comment

Popular posts from this blog

VLSI: 1-4 DEMUX (Demultiplexer) Dataflow Modelling with Testbench

-
Image
Verilog Code for 1-4 DEMUX Dataflow Modelling module demux_1_to_4(     input d,     input s0,     input s1,     output y0,     output y1,     output y2,     output y3     ); assign s1n = ~ s1; assign s0n = ~ s0; assign y0 = d& s0n & s1n; assign y1 = d & s0 & s1n; assign y2 = d & s0n & s1; assign y3 = d & s0 & s1; endmodule //Testbench code for 1-4 DEMUX Dataflow Modelling initial begin                              // Initialize Inputs ...
Read more

VLSI: BCD to Excess 3 and Excess 3 to BCD Dataflow Modelling

-
Image
module bcd_ex3_Dataflow(     input a,     input b,     input c,     input d,     output w,     output x,     output y,     output z     ); assign w = (a | (b & c) | (b & d)); assign x = (((~b) & c) | ((~b) & d) | (b & (~c) & (~d))); assign y = ((c & d) | ((~c) & (~d))); assign z = ~d; endmodule Excess 3 to BCD: module ex3_to_bcd(     input w,     input x,     input y,     input z,     output a,     output b,     output c,     output d     ); assign a = ((w & x) | (w & y & z)); assign b = (((~x) & (~y)) | ((~x) & (~z)) | (x & y & z)); assign c = (((~y) & z) | (y & (~z))); assign d = ~z; endmodule
Read more

Full Subtractor Verilog Code in Structural/Gate Level Modelling with Testbench

-
Image
Verilog Code for Full Subtractor Structural/Gate Level Modelling module  full_sub(borrow,diff,a,b,c); output  borrow,diff; input  a,b,c; wire w1,w4,w5,w6; xor (diff,a,b,c); not n1(w1,a); and a1(w4,w1,b); and a2(w5,w1,c); and a3(w6,b,c); or o1(borrow,w4,w5,w6); endmodule //Testbench code for Full Subtractor Structural/Gate Level Modelling initial  begin // Initialize Inputs a = 0; b = 0; c = 0; // Wait 100 ns for global reset to finish #100; // Add stimulus here #100; a = 0;b = 0;c = 1; #100; a = 0;b = 1;c = 0; #100; a = 0;b = 1;c = 1; #100; a = 1;b = 0;c = 0; #100; a = 1;b = 0;c = 1; #100; a = 1;b = 1;c = 0; #100; a = 1;b = 1;c = 1; end Output: RTL Schematic: Full Subtractor Verilog Other Verilog Programs: Go to Index of  Verilog Programming
Read more

Verilog: 4 to 2 Encoder Behavioral Modelling using Case Statement with Testbench Code

-
Image
Verilog Code for 4 to 2 Encoder Behavioral Modelling using Case Statement with Testbench Code module 4_2_ENC(      input [3:0]din,      output [1:0]dout      ); reg [1:0]dout; always @ (din) case (din)     1 : dout[0] = 0;      2 : dout[1] = 1;      4 : dout[2] = 2;      8 : dout[3] = 3;       default : dout = 2’bxx; endcase endmodule //Testbench code for 4 to 2 Encoder Behavioral Modelling using Case Statement initial  begin // Initialize Inputs   din = 0; // Wait 100 ns for global reset to finish #100; // Add stimulus here   #100; din=1;  #100; din=2;  #100; din=4;  #100; din=8; end initial begin  #100   $monitor (“ din=%b, dout=%b”, din, dout);  end  endmodule Xillinx Output: 4 - 2 Encoder Behavioral Modelling Verilog Response
Read more

VLSI: 8-3 Encoder Dataflow Modelling with Testbench

-
Image
Verilog Code for 8-3 Encoder Dataflow Modelling module encoder_8_to_3(     input d0,     input d1,     input d2,     input d3,     input d4,     input d5,     input d6,     input d7,     output q0,     output q1,     output q2     ); assign q0 = ( d1 | d3 | d5 | d7 ); assign q1 = ( d2 | d3 | d6 | d7 ); assign q2 = ( d4 | d6 | d5 | d7 ); endmodule //Testbench code for 8-3 Encoder Dataflow Modelling initial begin                         ...
Read more